{"title":"Ceiling Fan Remote Control Kit","description":"\u003cp\u003eAnderic has assembled a comprehensive range of ceiling fan remote control kits designed to seamlessly integrate with a wide variety of ceiling fans. Our collection includes Remote Controls and Receivers suitable for most major brands, as well as dedicated options for specific fans. Explore our selection today.\u003c\/p\u003e","products":[{"product_id":"anderic-fan53tb-universal-3-speed-with-receiver-315mhz-ceiling-fan-remote-control-kit","title":"Anderic Substitute Kit for FAN53TB \/ FAN42R 315MHz Ceiling Fan Remote Kit [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute kit for the FAN53TB \/ FAN42R 315 MHz kit: a matched ceiling fan remote and receiver with 16 dip codes.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF): 314.92 MHz\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003e16 dip-switch code combinations to avoid interference with nearby fans\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIt comes with its own remote and receiver. It does not pair with an existing 315 MHz FAN53TB remote or FAN42R receiver; replace both.\u003c\/li\u003e\n\u003cli\u003eThe receiver must be wired into the fan canopy.\u003c\/li\u003e\n\u003cli\u003eIt pairs by dip switches, not by learning.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWorks with many ceiling fans, including models starting with TG44, TG52 and BRD60.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to the full compatible models list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":50325335572791,"sku":"87949-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-universal-ceiling-fan-remote-kit_f75ceda9-4fff-414b-814a-c146ef8faabc.jpg?v=1783465127"},{"product_id":"mr77a-2-rr7222t434-replacement-ceiling-fan-kit","title":"Anderic MR77A.2-RR7222T434-KIT Altura Ceiling Fan Remote Control Kit for Home Decorators Collection","description":"\u003cp\u003eThe Anderic MR77A.2-RR7222T434-KIT is a matched receiver and remote kit for the Home Decorators Collection Altura 68 in. and similar fans.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic MR77A.2-RR7222T434-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF): 433.92 MHz\u003c\/li\u003e\n\u003cli\u003eBattery: 1 23A (not included)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIt comes with its own receiver and remote; the existing receiver and remote are not used.\u003c\/li\u003e\n\u003cli\u003eReverse works when the fan is running at low speed.\u003c\/li\u003e\n\u003cli\u003eTurn off power at the circuit breaker or fuse box before opening the fan canopy or housing. A qualified electrician is recommended.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003eRequire breaker or fuse isolation before opening the canopy or changing connectors or wiring. Wall-switch power cycling is for closed-housing pairing only. Reassemble the housing before restoring power. Keep the exact 434 MHz RR7222T434 pairing; this is not a 304 MHz procedure.\u003c\/p\u003e\n\n\u003col\u003e\n\u003cli\u003eTurn off the power to the fan at the circuit breaker or wall switch. A qualified electrician is recommended.\u003c\/li\u003e\n\u003cli\u003eOpen the fan housing, unscrew and unplug the old receiver, and keep the screws. Plug in the new receiver so the 9-pin square plug clicks into place; if you have a light kit, also connect the blue and white light wires (use wire nuts if the plugs do not line up). Secure the receiver with the screws and reinstall the housing.\u003c\/li\u003e\n\u003cli\u003eOn the remote, press firmly on the arrow and slide the battery cover off. Insert an 23A (12V) battery (not included), matching the polarity marks.\u003c\/li\u003e\n\u003cli\u003eSlide the remote's four code switches to a pattern of your choice. Avoid the default position, and use a different pattern for each fan. The receiver has no switches; it learns the remote's pattern in the next steps.\u003c\/li\u003e\n\u003cli\u003eTurn the fan power off at the circuit breaker or wall switch, then restore it.\u003c\/li\u003e\n\u003cli\u003eWithin 30 seconds, press and hold POWER (FAN OFF) for up to 10 seconds. The fan's downlight blinks twice when it pairs; a fan without a light gives no signal, so test with a speed key.\u003c\/li\u003e\n\u003cli\u003eIf it does not pair, repeat the power cycle and the previous step. If it still fails, check the FCC ID on the remote: CHQ7222T is 304 MHz and works with MR7703\/UC7301R receivers; CHQ7222T434, TR171B and KUJCE10205 are 434 MHz and work with MR77A receivers.\u003c\/li\u003e\n\u003cli\u003eTo dim the light, set the DIM switch inside the battery compartment to ON, then press and hold LIGHT.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver\u003c\/li\u003e\n\u003cli\u003eBattery not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHome Decorators Collection Altura 68 in. and fans that use MR77A receivers with CHQ7222T434 remotes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":47215468937527,"sku":"190234-NEW","price":79.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic_mr77a-rr7222t434-kit_2_a30fe815-156e-442e-8944-06e49707809a.jpg?v=1788371866"},{"product_id":"hd3-ac8-3-t-universal-thermostatic-kit-for-3-speed-ceiling-fan","title":"Anderic HD3\/AC8.3.T-KIT Thermostatic Add-on Ceiling Fan Kit with Remote Control with Receiver","description":"\u003cp\u003eThe Anderic HD3\/AC8.3.T-KIT is a thermostatic remote and receiver add-on kit for standard downrod-style ceiling fans.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic HD3\/AC8.3.T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eThermostatic temperature control\u003c\/li\u003e\n\u003cli\u003eWalk-away time delay, breeze mode and 2, 4 or 8 hour timer\u003c\/li\u003e\n\u003cli\u003eIncludes a compact receiver (1-7\/8 in. W x 3-3\/4 in. H x 1 in. D) and remote wall mount\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNot for hugger-style fans.\u003c\/li\u003e\n\u003cli\u003eFollow the installation instructions included with the kit; for wiring questions, use a licensed electrician.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eSetting the code on the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eRemove the battery cover by pressing firmly on the arrow and sliding it off.\u003c\/li\u003e\n\u003cli\u003eSlide the code switches up or down to your choice. The factory setting is up.\u003c\/li\u003e\n\u003cli\u003eThe remote shows °F from the factory; slide the °C\/°F dip switch to show °C.\u003c\/li\u003e\n\u003cli\u003eFor incandescent bulbs, slide the O\/D dip switch to \"D\"; otherwise slide it to \"O\".\u003c\/li\u003e\n\u003cli\u003eInstall 2 AAA batteries (not included) and replace the cover.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003eSetting the code on the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eSlide the receiver's code switches to EXACTLY the same positions as on the remote. The remote will not work unless both codes match.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003eTroubleshooting\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMake sure the wall switch is on.\u003c\/li\u003e\n\u003cli\u003eCheck the battery in the remote and stay within 10–20 ft.\u003c\/li\u003e\n\u003cli\u003eMake sure the dip switch settings are the same on the remote and receiver; turn off the power before checking the receiver switches.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver\u003c\/li\u003e\n\u003cli\u003eWall mount bracket\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWorks with many Home Decorators Collection ceiling fans, including models such as IN2RX13, KUJCE10407 and TR106A.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to the full compatible models list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":47215470313783,"sku":"196696-NEW","price":34.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic_hd3-ac8-3-t-kit_11.jpg?v=1767720549"},{"product_id":"63t-ac83t-kit-universal-3-speed-with-timer-for-led-ceiling-fan-remote-kit","title":"Anderic 63T-AC83T-KIT Add-on Remote Control Kit for LED 3-Speed Ceiling Fans","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWorks with many Harbor Breeze ceiling fans, including models such as A25-TX006, A25-43-L, A25-TX006-R and TFR-003.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to the full compatible models list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":47215488696631,"sku":"277444-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/63t-ac83t-kit-universal-3-speed-with-timer-for-led-ceiling-fan-remote-kit_01_489756b4-448a-4f4b-88bc-737d15957339.jpg?v=1768848861"},{"product_id":"anderic-universal-3-speed-wifi-works-with-google-alexa-ceiling-fan-remote-control-kit","title":"Anderic UC7235T4 Smart WIFI Ceiling Fan Receiver \u0026 Remote Control Kit - Works with Google Home \u0026 Alexa","description":"\u003cp\u003eThe Anderic UC7235T4 is a Wi-Fi ceiling fan receiver and remote control kit for 3-speed AC fans that works with the SmartLife, Tuya Smart or Atmosync apps.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic UC7235T4\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBattery: 1 CR2032 (not included)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIt does not work with the FanSync, Hubspace or SimpleConnect apps.\u003c\/li\u003e\n\u003cli\u003eThe receiver is wired into the fan canopy.\u003c\/li\u003e\n\u003cli\u003eKey names, layout and the look of the case may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eTurn off the power at the breaker. Leave a pull-chain light kit in the on position and the fan on its highest speed before installing the receiver.\u003c\/li\u003e\n\u003cli\u003eConnect the fan's white wire to the receiver wire marked TO MOTOR N, the fan's black wire to TO MOTOR L and the fan's blue wire to For Light; connect the house neutral (white) to AC in N and the house hot (black) to AC in L. Secure all connections with wire nuts.\u003c\/li\u003e\n\u003cli\u003eInstall the battery in the remote (not included), then restore power to the fan.\u003c\/li\u003e\n\u003cli\u003eWithin 60 seconds of turning the power on, press and hold FAN OFF for 5 seconds. The fan lights blink to confirm pairing.\u003c\/li\u003e\n\u003cli\u003eIf they do not blink, turn the power off and repeat step 4. Then add the fan in the SmartLife, Tuya Smart or Atmosync app if you want phone or voice control.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver\u003c\/li\u003e\n\u003cli\u003eWall mount bracket\u003c\/li\u003e\n\u003cli\u003eBattery not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eWorks with 3-speed AC ceiling fans.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":47215488827703,"sku":"277912-NEW","price":49.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/UC7235T4-KIT_c18f8dbf-1914-46d4-846c-2ec9961009ad.png?v=1788549943"},{"product_id":"hampton-bay-18rhd5kit-ceiling-fan-remote-control-kit","title":"Anderic Substitute Kit for Hampton Bay 18RHD5KIT Ceiling Fan Remote Control Kit [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Hampton Bay 18RHD5KIT kit. It is a ceiling fan remote and receiver kit (16 dip codes). It works with ceiling fans such as 18R, HD5 and UC7078T Receiver.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHampton Bay 18RHD5KIT\u003c\/li\u003e\n\u003cli\u003eSupplied with: 18R, HD5, UC7078T Receiver\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Substitute (63T-AC83T-KIT)","offer_id":50325394587959,"sku":"63T-AC83T-KIT\u003c66893-SUB","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/63t-ac83t-kit-universal-3-speed-with-timer-for-led-ceiling-fan-remote-kit_01_jpg_13ba1471-97bf-4a93-80fe-51ed30f12dcf.jpg?v=1783465136"},{"product_id":"hampton-bay-fan28rudlkit-ceiling-fan-remote-control-kit","title":"Anderic Substitute Kit for Hampton Bay UC7078T (UP \u0026 DOWN LIGHT) \u0026 FAN28R Ceiling Fan Remote Control Kit [RR7078TUDLKIT]","description":"\u003cp\u003eThe Anderic RR7078TUDLKIT is a substitute kit for the Hampton Bay UC7078T \/ FAN28R kit. It is a 304 MHz ceiling fan remote and receiver kit for fans with up and down lights, and it pairs by matching dip switches.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic RR7078TUDLKIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF): 304 MHz\u003c\/li\u003e\n\u003cli\u003eBattery: 1 9-Volt (not included)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e304 MHz only\u003c\/li\u003e\n\u003cli\u003eFor 3-speed AC ceiling fans with up and down lights\u003c\/li\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003eWith the breaker OFF, install the receiver and set or record its code switches; set the remote to the identical pattern, close all covers and the canopy, then restore power and test. Remote-only code trials may be done without opening an energized receiver.\u003c\/p\u003e\n\n\u003col\u003e\n\u003cli\u003eTurn the power to the fan off at the circuit breaker. Install the receiver in the fan canopy following the wiring instructions included with the kit, then restore power.\u003c\/li\u003e\n\u003cli\u003eRemove the remote's battery cover: push firmly below the arrow and slide it off. Set the code switches before installing the battery, because on some models the battery covers the switch panel.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the 4 code (dip) switches up or down to a pattern of your choice. The factory setting is all up.\u003c\/li\u003e\n\u003cli\u003eSet the 4 code switches on the fan's receiver to exactly the same pattern as the remote. The remote and receiver only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert the battery (not included), matching the polarity marks, and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press a fan speed key and the light key. The fan and light respond when the patterns match.\u003c\/li\u003e\n\u003cli\u003eIf you cannot reach the receiver: set the remote's switches to one of the 16 patterns, press a key to test, and if the fan does not respond, move to the next pattern. Repeat until the fan responds.\u003c\/li\u003e\n\u003cli\u003eIf the fan or light turns on and off by itself, another remote is interfering: set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver\u003c\/li\u003e\n\u003cli\u003eBattery not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHampton Bay UC7078T \/ FAN28R\u003c\/li\u003e\n\u003cli\u003eSupplied with: UC7067RC\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":50325399601463,"sku":"67127-NEW","price":44.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/FAN28RUDLKIT_1_3da9fea5-ae1b-4bca-80ce-f7aa961867d9.jpg?v=1783617951"},{"product_id":"hampton-bay-fan28rhd5kit-ceiling-fan-remote-control-kit","title":"Anderic Substitute Kit for Hampton Bay FAN28R HD5 KIT Ceiling Fan Remote Control Kit [RR7079TKIT]","description":"\u003cp\u003eThe Anderic RR7079TKIT is a substitute for the Hampton Bay FAN28R \/ HD5 kit. It is a 304 MHz ceiling fan remote and receiver kit that pairs by matching dip switches.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic RR7079TKIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF): 303.9 MHz\u003c\/li\u003e\n\u003cli\u003eBattery: 1 9-Volt (not included)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e304 MHz only\u003c\/li\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003eWith the breaker OFF, install the receiver and set or record its code switches; set the remote to the identical pattern, close all covers and the canopy, then restore power and test. Remote-only code trials may be done without opening an energized receiver.\u003c\/p\u003e\n\n\u003col\u003e\n\u003cli\u003eTurn the power to the fan off at the circuit breaker. Install the receiver in the fan canopy following the wiring instructions included with the kit, then restore power.\u003c\/li\u003e\n\u003cli\u003eRemove the remote's battery cover: push firmly below the arrow and slide it off. Set the code switches before installing the battery, because on some models the battery covers the switch panel.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the 4 code (dip) switches up or down to a pattern of your choice. The factory setting is all up.\u003c\/li\u003e\n\u003cli\u003eSet the 4 code switches on the fan's receiver to exactly the same pattern as the remote. The remote and receiver only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert the battery (not included), matching the polarity marks, and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press a fan speed key and the light key. The fan and light respond when the patterns match.\u003c\/li\u003e\n\u003cli\u003eIf you cannot reach the receiver: set the remote's switches to one of the 16 patterns, press a key to test, and if the fan does not respond, move to the next pattern. Repeat until the fan responds.\u003c\/li\u003e\n\u003cli\u003eIf the fan or light turns on and off by itself, another remote is interfering: set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver\u003c\/li\u003e\n\u003cli\u003eWall mount bracket\u003c\/li\u003e\n\u003cli\u003eBattery not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHampton Bay FAN28R \/ HD5\u003c\/li\u003e\n\u003cli\u003eAlso works with: 18R, UC7078T Receiver\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":50325389246775,"sku":"78693-NEW","price":49.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic_rr7079tkit_5.jpg?v=1762198966"},{"product_id":"hunter-27185060kit-ceiling-fan-remote-control-kit","title":"Anderic Substitute Kit for Hunter 27185-060 Ceiling Fan Remote Control Kit [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Hunter 27185-060 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHunter 27185-060\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":50325386395959,"sku":"79080-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-kit_c13efb15-aa94-44e7-a82c-7b44655e2e68.jpg?v=1783465141"},{"product_id":"include-23a-12v-battery","title":"(1 Pack) 23A, 12V Battery","description":"\u003cp\u003eThis battery is great for ceiling fan remote controls, garage door remotes and much more.  \u003c\/p\u003e\n\u003cp\u003e23A-12V\u003cbr\u003e12 Volt battery\u003cbr\u003eOne Battery\u003c\/p\u003e","brand":"Include","offers":[{"title":"Default Title","offer_id":49697884176695,"sku":"87839-NEW","price":1.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/A23-battery.jpg?v=1762200871"},{"product_id":"nutone-rck01-universal-ceiling-fan-kit-ceiling-fan-remote-control-kit","title":"Anderic Substitute Kit for Nutone RCK01 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Nutone RCK01 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003eBefore reopening the canopy or touching the receiver DIP switches, wiring or antenna, switch the breaker OFF again. Complete and insulate all connections, safely cap any unused light lead where applicable, close the canopy, then restore power. Cycling a wall switch is not permission to service an energized receiver.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNutone RCK01\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":50325381447991,"sku":"88606-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control-kit_c359cb94-47a9-4e4d-8f9d-91fc0376150b.jpg?v=1783465146"},{"product_id":"harbor-breeze-40837-ceiling-fan-remote-control-kit","title":"Harbor Breeze 40837 Ceiling Fan Remote Control Kit","description":"\u003cp\u003eThe Harbor Breeze 40837 kit adds wireless remote control to a Harbor Breeze ceiling fan.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBattery: 1 A23 (not included)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit installs in the fan.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eRe-syncing the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eThe remote is synced at the factory. To re-sync, turn off the main power, then turn it back on.\u003c\/li\u003e\n\u003cli\u003eWithin 30 seconds, use a small screwdriver to press and hold the learn button on the remote for 3 seconds.\u003c\/li\u003e\n\u003cli\u003eThe fan turns on and the light (if any) blinks three times to confirm.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver\u003c\/li\u003e\n\u003cli\u003eBattery not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eWorks with Harbor Breeze ceiling fans.\u003c\/p\u003e","brand":"Dan's Originals","offers":[{"title":"Original","offer_id":50325375844663,"sku":"202984-NEW","price":12.0,"currency_code":"USD","in_stock":false},{"title":"Substitute","offer_id":50325375877431,"sku":"202984-NEW-2","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/harbor-breeze_0745359_2_83711242-b41d-4f4e-b677-e837bf1549a7.jpg?v=1762201808"},{"product_id":"harbor-breeze-tr258b-kujce10716-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Harbor Breeze TR258B KUJCE10716 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Harbor Breeze TR258B \/ KUJCE10716 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHarbor Breeze TR258B \/ KUJCE10716\u003c\/li\u003e\n\u003cli\u003eWorks with many Harbor Breeze ceiling fans, including models such as 0599656, 0599848 and 0599849.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to the full compatible models list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49698574106935,"sku":"276824-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/harbor-breeze-tr258b-kujce10716-ceiling-fan-remote-control_01_76a49050-e3a0-4489-afa6-27ef1483fd46.jpg?v=1783464805"},{"product_id":"hampton-bay-tr222a-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Hampton Bay TR222A Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Hampton Bay TR222A kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHampton Bay TR222A\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49698588786999,"sku":"277661-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_6145aeaa-1c06-4b23-aea3-14757e7d3d46.jpg?v=1783464811"},{"product_id":"hampton-bay-tx029rs-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Hampton Bay TX029RS Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Hampton Bay TX029RS kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003eThe supplied 63T kit has one light output and does not provide independent upper and down-light channels. It does not retain every original TX029RS lighting function. Exact fan fit depends on correct mechanical and electrical installation.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHampton Bay TX029RS\u003c\/li\u003e\n\u003cli\u003eWorks with many Hampton Bay ceiling fans, including models such as YG768APN, YG768AWH and YG654BN.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to the full compatible models list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49698590130487,"sku":"277803-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_c33f0aab-4ed0-4ef3-b53b-dc546d8a5669.jpg?v=1783464817"},{"product_id":"hampton-bay-tx028lr-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Hampton Bay TX028LR Ceiling Fan Remote Control - A25TX028LR [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Hampton Bay TX028LR \/ A25TX028LR kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHampton Bay TX028LR \/ A25TX028LR\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49698590294327,"sku":"277809-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_8f1ac64a-31a6-403c-9cdb-4c9d1dcd6edc.jpg?v=1783464823"},{"product_id":"hampton-bay-tx028-rs-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Hampton Bay TX028-RS Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Hampton Bay TX028-RS kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHampton Bay TX028-RS\u003c\/li\u003e\n\u003cli\u003eWorks with many Hampton Bay ceiling fans, including models such as 52192, 52020 and 52021.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to the full compatible models list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49698590359863,"sku":"277812-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_60d86e6f-c21a-453f-8e14-df77a3be5acf.jpg?v=1783464829"},{"product_id":"hampton-bay-tx028c-lc-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Hampton Bay TX028C-LC Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Hampton Bay TX028C-LC kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHampton Bay TX028C-LC\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49698590720311,"sku":"277822-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_ffa42085-ccfd-4c16-8ea3-1de6c4efcc51.jpg?v=1783464835"},{"product_id":"hampton-bay-a25-tx029-lr-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Hampton Bay A25-TX029-LR Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Hampton Bay A25-TX029-LR kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHampton Bay A25-TX029-LR\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49698591080759,"sku":"277827-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/hampton-bay-a25-tx029-lr-ceiling-fan-remote-control_01_f8c799d1-f6f0-45b3-943e-f9719fcc2d32.jpg?v=1783459048"},{"product_id":"harbor-breeze-a25tx013-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Harbor Breeze A25TX013 TX013-R Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Harbor Breeze A25TX013 \/ TX013-R kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHarbor Breeze A25TX013 \/ TX013-R\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49698591899959,"sku":"277854-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/harbor-breeze-a25tx013-ceiling-fan-remote-control_01_c3823424-7592-4ecf-92b9-7d0fc603c05f.jpg?v=1783459055"},{"product_id":"home-decorators-collection-tra048g1m-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Home Decorators Collection TRA048G1M Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Home Decorators Collection TRA048G1M kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003eComplete all receiver DIP, wiring, and canopy work with the circuit breaker off; reassemble, then restore power to test. If you later need to access the receiver again, isolate power at the breaker first.\u003c\/p\u003e\n\n\u003cp\u003eTurn off power at the circuit breaker before opening the canopy or touching or adjusting the receiver. Match or record receiver switches with power off; close covers, then restore power to test. If you are not opening the receiver, you may try remote-only code patterns.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHome Decorators Collection TRA048G1M\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49698633351479,"sku":"280380-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_ddd54909-babc-4762-baca-a0d14e7ab750.jpg?v=1783459072"},{"product_id":"fanimation-fans-rh786r-up-down-light-ceiling-fan-receiver","title":"Anderic Substitute Kit for Fanimation Fans RH786R Up\/down light Ceiling Fan Receiver [RH786R\/RR787T-KIT]","description":"\u003cp\u003eThe Anderic RH786R\/RR787T-KIT is a substitute kit for the Fanimation RH786R receiver: an RH786R receiver and an RR787T remote.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic RH786R\/RR787T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBattery: 1 23A (not included)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIt works only with fans that came with the RH786R receiver. It does not work with fans that use a different receiver style.\u003c\/li\u003e\n\u003cli\u003eThe receiver works only with the RH787T or RR787T remote.\u003c\/li\u003e\n\u003cli\u003eKey names and layout differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eTurn off the power at the circuit breaker or fuse box. Unplug the old receiver and plug in the RH786R, following your fan's instructions.\u003c\/li\u003e\n\u003cli\u003eRemove the remote's battery cover and set its dip switches to any setting you choose; the fan learns the setting. Install the 23A battery (not included).\u003c\/li\u003e\n\u003cli\u003eRestore power to the fan. Do not press any other button before SET.\u003c\/li\u003e\n\u003cli\u003eWithin 60 seconds of restoring power, press and hold SET for 1 to 5 seconds.\u003c\/li\u003e\n\u003cli\u003eThe light blinks twice: the fan now responds to the remote.\u003c\/li\u003e\n\u003cli\u003eIf you pressed another button first or it does not pair, turn the power off and on again and repeat from step 3.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver\u003c\/li\u003e\n\u003cli\u003eBattery not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eListed for the Fanimation RH786R. Works with fans that used the RH786R receiver\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749959311671,"sku":"278171-NEW","price":94.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/fanimation-fans-rh786r-up-down-light-ceiling-fan-receiver_01_ac16943f-80dd-4b55-b4eb-c4802b554f70.jpg?v=1783622003"},{"product_id":"ge-general-electric-fan61t-3sp1-ceiling-fan-remote-control","title":"Anderic Substitute Kit for GE General Electric FAN61T-3SP1 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the GE General Electric FAN61T-3SP1 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eGE General Electric FAN61T-3SP1\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":50324896252215,"sku":"204849-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/ge-general-electric-fan61t-3sp1-ceiling-fan-remote-control_01_14684b9c-4c29-403c-9043-f6b5b865e59e.jpg?v=1783459093"},{"product_id":"generic-10442-better-homes-and-gardens-universal-3-speed-ceiling-fan-remote-control-kit","title":"Dan's Originals 10442 Better Homes and Gardens 3 Speed Ceiling Fan Remote Control Kit","description":"\u003cp\u003eThe Better Homes and Gardens 10442 is a 3-speed ceiling fan remote control kit for fan speed and light control.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBattery: 1 A23 (not included)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThe kit replaces your fan's existing control with its own receiver\u003c\/li\u003e\n\u003cli\u003eCheck that your fan is an AC ceiling fan with room in the canopy for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries are not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver\u003c\/li\u003e\n\u003cli\u003eBattery not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eWorks with Better Homes and Gardens and other AC ceiling fans with room in the canopy for the receiver.\u003c\/p\u003e","brand":"Dan's Originals","offers":[{"title":"Original","offer_id":50325374533943,"sku":"278322-NEW","price":19.99,"currency_code":"USD","in_stock":false},{"title":"Substitute","offer_id":50325374566711,"sku":"278322-NEW-2","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/generic_10442_3.jpg?v=1762269360"},{"product_id":"generic-dl4110t-ceiling-fan-remote-control","title":"Anderic Substitute Kit for DL4110T Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the DL4110T kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDL4110T\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749986804023,"sku":"277923-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-dl4110t-ceiling-fan-remote.jpg?v=1783459098"},{"product_id":"generic-dl6101t-ceiling-fan-remote-control","title":"Anderic Substitute Kit for DL6101T Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the DL6101T kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDL6101T\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749987328311,"sku":"277918-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_b1a02d2d-eedb-4c8e-9c86-9bda450e1cf1.jpg?v=1783459104"},{"product_id":"generic-fan57t-ceiling-fan-remote-control","title":"Anderic Substitute Kit for FAN57T Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the FAN57T kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eFAN57T\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749987590455,"sku":"277869-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-fan57t-ceiling-fan-remote.jpg?v=1783459109"},{"product_id":"generic-fan61t-3s-ceiling-fan-remote-control","title":"Anderic Substitute Kit for GE FAN61T-3S Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the GE FAN61T-3S kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eGE FAN61T-3S\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749987754295,"sku":"277871-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ge-ceiling-fan-remote_640194c4-671f-41bb-a101-ebee2dd8641f.jpg?v=1783459115"},{"product_id":"generic-fan61t-4s-ceiling-fan-remote-control","title":"Anderic Substitute Kit for GE FAN61T-4S Ceiling Fan Remote Control - 2AAZPAC6 [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the GE FAN61T-4S \/ 2AAZPAC6 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eGE FAN61T-4S \/ 2AAZPAC6\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749987852599,"sku":"DAN-FAN61T4S-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-white-ceiling-fan-remote-control.jpg?v=1783459120"},{"product_id":"generic-fan61t-4sp1-ceiling-fan-remote-control","title":"Anderic Substitute Kit for GE FAN61T-4SP1 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the GE FAN61T-4SP1 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eGE FAN61T-4SP1\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749988180279,"sku":"277867-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ge-ceiling-fan-remote-control.jpg?v=1783459126"},{"product_id":"generic-kuj9301-ceiling-fan-remote-control","title":"Anderic Substitute Kit for KUJ9301 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the KUJ9301 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKUJ9301\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749989196087,"sku":"277696-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_cb16dd21-beeb-498f-9f27-6455bd82db9a.jpg?v=1783459131"},{"product_id":"generic-kuj9302-ceiling-fan-remote-control","title":"Anderic Substitute Kit for KUJ9302 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the KUJ9302 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKUJ9302\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749989622071,"sku":"277695-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_c3924ae1-e307-4447-8491-f6214f3f0a6b.jpg?v=1783459137"},{"product_id":"generic-kuj9303-ceiling-fan-remote-control","title":"Anderic Substitute Kit for KUJ9303 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the KUJ9303 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKUJ9303\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749989785911,"sku":"277694-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-kuj9303-ceiling-fan-remote.jpg?v=1783459142"},{"product_id":"generic-kujce10203-ceiling-fan-remote-control","title":"Anderic Substitute Kit for KUJCE10203 Ceiling Fan Remote Control [RR7099TKIT]","description":"\u003cp\u003eThe Anderic RR7099TKIT is a substitute kit for the KUJCE10203 remote. It is a ceiling fan remote and receiver kit with a wall mount.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eShipped kit: Anderic RR7099TKIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF): 304 MHz\u003c\/li\u003e\n\u003cli\u003eBattery: 1 9-Volt (not included)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDoes not work with fans that use the KUJCE9201 system\u003c\/li\u003e\n\u003cli\u003eThe receiver must be installed in the fan\u003c\/li\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003cli\u003eThis is a kit that includes a receiver; the KUJCE10203 is a remote only.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power to the fan off at the circuit breaker. Install the receiver in the fan canopy following the wiring instructions included with the kit, then restore power.\u003c\/li\u003e\n\u003cli\u003eRemove the remote's battery cover: push firmly below the arrow and slide it off. Set the code switches before installing the battery, because on some models the battery covers the switch panel.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the 4 code (dip) switches up or down to a pattern of your choice. The factory setting is all up.\u003c\/li\u003e\n\u003cli\u003eSet the 4 code switches on the fan's receiver to exactly the same pattern as the remote. The remote and receiver only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert the battery (not included), matching the polarity marks, and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press a fan speed key and the light key. The fan and light respond when the patterns match.\u003c\/li\u003e\n\u003cli\u003eIf you cannot reach the receiver: set the remote's switches to one of the 16 patterns, press a key to test, and if the fan does not respond, move to the next pattern. Repeat until the fan responds.\u003c\/li\u003e\n\u003cli\u003eIf the fan or light turns on and off by itself, another remote is interfering: set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 Anderic RR7099T remote and 1 UC7067FCRX receiver\u003c\/li\u003e\n\u003cli\u003eWall mount bracket\u003c\/li\u003e\n\u003cli\u003eBattery not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKUJCE10203\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749990736183,"sku":"277673-NEW","price":54.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-generics_kujce10203_2_d9f7f632-b31d-49b4-b08a-b00a24e3ccf3.jpg?v=1783624515"},{"product_id":"generic-kujce10206-ceiling-fan-remote-control","title":"Anderic Substitute Kit for KUJCE10206 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the KUJCE10206 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKUJCE10206\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749990900023,"sku":"277671-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/generic-kujce10206-ceiling-fan-remote-control_01_58cd8f62-4227-4728-8826-0d03e6a2f1e4.jpg?v=1783457802"},{"product_id":"generic-kujce10608-ceiling-fan-remote-control","title":"Anderic Substitute Kit for KUJCE10608 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the KUJCE10608 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKUJCE10608\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749992833335,"sku":"277630-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-generics_kujce10608_2_5558fe0e-e73e-4ab3-b5d6-d59205e09dc4.jpg?v=1783457807"},{"product_id":"generic-kujce10720-ceiling-fan-remote-control","title":"Anderic Substitute Kit for KUJCE10720 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the KUJCE10720 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKUJCE10720\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749993128247,"sku":"277605-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-generics_kujce10720_2_8fca623a-127e-4615-b541-01586f796c7d.jpg?v=1783457818"},{"product_id":"generic-kujce9101-ceiling-fan-remote-control","title":"Anderic Substitute Kit for KUJCE9101 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the KUJCE9101 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKUJCE9101\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749994209591,"sku":"277698-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_d147a94a-838b-409d-926c-25d323e4cdc2.jpg?v=1783457823"},{"product_id":"generic-kujce9811-ceiling-fan-remote-control","title":"Anderic Substitute Kit for KUJCE9811 Ceiling Fan Remote Control [MR77A-RR7222T434-KIT]","description":"\u003cp\u003eThe Anderic MR77A-RR7222T434-KIT is a substitute kit for the KUJCE9811. It is a 434 MHz ceiling fan remote and receiver set for MR77A-type fans.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic MR77A-RR7222T434-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF): 433.9 MHz\u003c\/li\u003e\n\u003cli\u003eBattery: 1 A23 (not included)\u003c\/li\u003e\n\u003cli\u003eIncludes the RRMR77A receiver, the RR7222T434 remote and a wall mount\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIt comes with its own receiver; your existing remote does not pair with it.\u003c\/li\u003e\n\u003cli\u003eIt is 434 MHz only: it does not work with 304 MHz CHQ7222T-family parts.\u003c\/li\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eTurn off power to the fan at the wall switch or circuit breaker. A qualified electrician is recommended for installing the receiver.\u003c\/li\u003e\n\u003cli\u003eOpen the fan housing, unscrew and unplug the old receiver, and keep the screws.\u003c\/li\u003e\n\u003cli\u003ePlug in the new receiver and make sure the 9-pin square plug clicks into place. If you have a light kit, also connect the blue and white light wires.\u003c\/li\u003e\n\u003cli\u003eSecure the new receiver in the same place with the existing screws, then reinstall the fan housing.\u003c\/li\u003e\n\u003cli\u003eOn the remote, press firmly on the arrow and slide the battery cover off. Insert an A23 (12V) battery, matching the polarity marks.\u003c\/li\u003e\n\u003cli\u003eSlide the four code switches to a pattern of your choice. Avoid the default position, and use a different pattern for each fan.\u003c\/li\u003e\n\u003cli\u003eTurn the fan power off at the circuit breaker or wall switch, then restore it.\u003c\/li\u003e\n\u003cli\u003eWithin 30 seconds, press and hold POWER (FAN OFF) for up to 10 seconds. The fan's downlight blinks twice when it pairs; a fan without a light gives no signal.\u003c\/li\u003e\n\u003cli\u003eTo dim the light, set the DIM switch inside the battery compartment to ON, then press and hold LIGHT.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver\u003c\/li\u003e\n\u003cli\u003eWall mount bracket\u003c\/li\u003e\n\u003cli\u003eBattery not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eListed for the KUJCE9811. Works with MR77A-type fans\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749995225399,"sku":"277684-NEW","price":79.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/MR77A-MOLEX-KIT-SQ-new1_54b7e2ec-56f2-44da-8211-0ffdceb3d5be.jpg?v=1788371872"},{"product_id":"generic-re-ac-h-1-uc7235t4-for-modern-fan-company-ceiling-fan-remote-control","title":"Anderic Substitute Kit for RE-AC-H-1 UC7235T4 for Modern Fan Company Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the RE-AC-H-1 \/ UC7235T4 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRE-AC-H-1 \/ UC7235T4\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749995847991,"sku":"277714-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-modern-fan-company-remote-control.jpg?v=1783457829"},{"product_id":"generic-tr106a-kujce10511-ceiling-fan-remote-control","title":"Anderic Substitute Kit for Design House KUJCE10511 Ceiling Fan Remote Control Kit - 154286 [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the Design House KUJCE10511 \/ 154286 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDesign House KUJCE10511 \/ 154286\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749996503351,"sku":"277633-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-white-ceiling-fan-remote_b50d795a-c753-4194-82d2-b4df3fbc96bd.jpg?v=1783457835"},{"product_id":"generic-tr121a-kujce10002-ceiling-fan-remote-control","title":"Anderic Substitute Kit for TR121A KUJCE10002 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the TR121A \/ KUJCE10002 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTR121A \/ KUJCE10002\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749997093175,"sku":"277680-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-white-ceiling-fan-remote_ef0a069f-1306-4e7b-baa2-d0e36332609c.jpg?v=1783457840"},{"product_id":"generic-tr123b-kujce10901-ceiling-fan-remote-control","title":"Anderic Substitute Kit for TR123B KUJCE10901 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the TR123B \/ KUJCE10901 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTR123B \/ KUJCE10901\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749997289783,"sku":"277599-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_8eb2eaba-5b33-4237-8403-36f68d2f1c61.jpg?v=1783457845"},{"product_id":"generic-tr158c-kujce10721-ceiling-fan-remote-control","title":"Anderic Substitute Kit for TR158C KUJCE10721 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the TR158C \/ KUJCE10721 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTR158C \/ KUJCE10721\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749997814071,"sku":"277601-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_0d4012ad-7ace-465e-a979-4b88b6b015e7.jpg?v=1783457850"},{"product_id":"generic-tr221a-ceiling-fan-remote-control","title":"Anderic Substitute Kit for TR221A Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the TR221A kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTR221A\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749998502199,"sku":"277662-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_a99ef42e-417c-48ec-86fd-0e2e667d7bff.jpg?v=1783451388"},{"product_id":"generic-tr262b-kujce10705-ceiling-fan-remote-control","title":"Anderic Substitute Kit for TR262B KUJCE10705 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the TR262B \/ KUJCE10705 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTR262B \/ KUJCE10705\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749998698807,"sku":"277600-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-tr262b-ceiling-fan-remote.jpg?v=1783451393"},{"product_id":"generic-tr313a-kujce10709-ceiling-fan-remote-control","title":"Anderic Substitute Kit for TR313A KUJCE10709 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the TR313A \/ KUJCE10709 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTR313A \/ KUJCE10709\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749998928183,"sku":"277617-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-white-ceiling-fan-remote.jpg?v=1783451398"},{"product_id":"generic-tr96b-kujce10703-ceiling-fan-remote-control","title":"Anderic Substitute Kit for TR96B KUJCE10703 Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the TR96B \/ KUJCE10703 kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTR96B \/ KUJCE10703\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49749999649079,"sku":"277604-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-ceiling-fan-remote-control_e69f29c0-d5c5-43e8-a9dd-7850f1c9f0a6.jpg?v=1783451403"},{"product_id":"generic-uc7082t-ceiling-fan-remote-control","title":"Anderic Substitute Kit for UC7082T Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the UC7082T kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eUC7082T\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49750000337207,"sku":"277749-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-white-ceiling-fan-remote_18ab2436-4de7-4b84-a705-aea15721b87d.jpg?v=1783451410"},{"product_id":"generic-uc7207t-ceiling-fan-remote-control","title":"Anderic Substitute Kit for UC7207T Ceiling Fan Remote Control [63T-AC83T-KIT]","description":"\u003cp\u003eThe Anderic 63T-AC83T-KIT is a substitute for the UC7207T kit. It is a ceiling fan remote and receiver kit (16 dip codes).\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKit: Anderic 63T-AC83T-KIT\u003c\/li\u003e\n\u003cli\u003eRadio frequency (RF)\u003c\/li\u003e\n\u003cli\u003eBatteries: 2 AAA (not included)\u003c\/li\u003e\n\u003cli\u003eFor AC ceiling fans only; not for DC or solid-state fans\u003c\/li\u003e\n\u003cli\u003eSupply: 110\/120 V, 60 Hz; maximum fan motor 1.0 A; maximum light 190 W (incandescent or LED)\u003c\/li\u003e\n\u003cli\u003eSeparate fan and light control: HIGH, MEDIUM, LOW and fan power keys\u003c\/li\u003e\n\u003cli\u003eLight key: press for on\/off, press and hold to dim; the receiver remembers the brightness\u003c\/li\u003e\n\u003cli\u003eTimer key for a 2, 4 or 8 hour light delay, shown by an LED on the remote\u003c\/li\u003e\n\u003cli\u003eOne remote can run two fans, or two remotes can run one fan, by matching dip switches\u003c\/li\u003e\n\u003cli\u003eWorks with fans that have no light kit (leave the blue light wire unconnected)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to Know\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKey names and layout may differ from the original. Compare your original's buttons before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup \/ Pairing\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e1. Install the receiver\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eTurn the power off at the circuit breaker or remove the fuse. A qualified electrician is recommended. Make sure the receiver fits in your fan canopy before you start.\u003c\/li\u003e\n\u003cli\u003eIf your fan has pull chains, set the fan chain to high speed and turn the light chain on.\u003c\/li\u003e\n\u003cli\u003eSet the receiver's 4 code switches to a pattern of your choice and note it. The factory setting is all up; we suggest not using it.\u003c\/li\u003e\n\u003cli\u003eRemove the fan canopy from the mounting bracket and disconnect the existing wiring between the fan and the ceiling junction box.\u003c\/li\u003e\n\u003cli\u003eConnect the receiver with the supplied wire nuts: green fan wire to the bare (ground) supply wire; black receiver wire AC IN L to the black wire from the ceiling; white receiver wire AC IN N to the white wire from the ceiling; white receiver wire TO MOTOR N to the white fan wire; black receiver wire TO MOTOR L to the black fan wire; blue receiver wire FOR LIGHT to the blue fan wire. If your wires are different colors, have a licensed electrician install it.\u003c\/li\u003e\n\u003cli\u003ePush the connections up into the junction box, lay the brown antenna wire on top of the receiver, set the receiver in the mounting bracket and reinstall the canopy.\u003c\/li\u003e\n\u003cli\u003eRestore power.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003e2. Pair the remote\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePress firmly on the arrow and slide the remote's battery cover off.\u003c\/li\u003e\n\u003cli\u003eWith a small screwdriver or pen tip, slide the remote's 4 code switches to exactly the same pattern as the receiver. The two only work together when the patterns match.\u003c\/li\u003e\n\u003cli\u003eInsert 2 AAA batteries (not included) and replace the battery cover.\u003c\/li\u003e\n\u003cli\u003eTest: press the fan speed keys, the power key and the light key. The blue indicator on the remote lights with each key press, and the fan and light respond.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch3\u003eTroubleshooting\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRemote does not work: check that the receiver has power and the wall switch is on, the wiring is correct, any pull chains are on high with the light on, the batteries are in correctly, and the code switches match on the remote and receiver.\u003c\/li\u003e\n\u003cli\u003eFan or light turns on and off by itself: another RF remote is interfering; set a new matching pattern on both the remote and the receiver.\u003c\/li\u003e\n\u003cli\u003eShort range: route the brown antenna wire higher, outside the junction box.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Box\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 remote and 1 receiver (63T-AC83T-KIT)\u003c\/li\u003e\n\u003cli\u003eWall mount holder and 2 screws\u003c\/li\u003e\n\u003cli\u003eWire nuts for the receiver\u003c\/li\u003e\n\u003cli\u003eBatteries not included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatible Models\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eUC7207T\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBefore ordering, check the model or part number printed on your old remote (usually on the back or inside the battery compartment) and compare it to this list.\u003c\/p\u003e","brand":"Anderic","offers":[{"title":"Default Title","offer_id":49750000763191,"sku":"277740-NEW","price":24.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/files\/anderic-uc7207t-ceiling-fan-remote.jpg?v=1783451415"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0837\/7634\/0279\/collections\/file_aa99887a-ba47-4488-848a-af19c488e987.jpg?v=1724094320","url":"https:\/\/www.anderic.com\/collections\/ceiling-fan-kit.oembed?page=8","provider":"Anderic","version":"1.0","type":"link"}